Schwinn 120 (2012 model) Uživatelský manuál

ASSEMBLY MANUAL / OWNER’S MANUAL Manual en Español Latino Americano:http://www.schwinnfitness.com

105. Attach Console Mast to Frame Assembly NOTICE: Do not crimp Console Cable. Note: Do not fully tighten the hardware.CBX46mm4. Connect Console M

116. Attach Handlebars to Frame Assembly NOTICE: Do not crimp the cables. Remove the pre-installed plug from the mast, route the HR cable through t

128. Attach Console to Console Mast Note: Align the Console on the Console Mast mounting plate and attach with the screws from S t e p 7. NOTICE:

139. Adjust the Console and Console Mast and Tighten Hardware Note: To install the Media Support, slide it into the holes at the top of the console.

1410. Install Water Bottle Holder on Console Mast Note: The hardware is pre-installed on the console mast and not on the hardware card.X213

1511. Connect AC Adapter to Frame Assembly12. Final InspectionInspect your machine to ensure that all hardware is tight and components are properly as

16Leveling Your BikeThe levelers are the polygonal end caps on the Rear Stabilizer. Turn the end cap to adjust the level. Makesurethebikeislevel

17!This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.Before using this equipment, obey

18A Console G PedalsB Handlebars, Upright H LevelerC Shrouded Main Frame I Adjustable SeatD Transport Wheel J Contact Heart Rate (CHR) SensorsE Stabil

19Console FeaturesThe Console provides important information about your workout and lets you control the resistancelevelswhileyouexercise.TheCon

2Important Safety Instructions - Assembly 3 Safety Warning Labels / Serial Number 4Specifications 5Before Assembly 5Parts 6Hardware 7Tools 7Assembl

20LCD Display DataProgram DisplayThe Program Display shows the name of the program selection and the grid area shows the course profile for the program

21Level / HR (Heart Rate)The LEVEL/HR display field shows the current resistance level (1–16) for 6 seconds, then your Heart Rate for 6 seconds. The HR

22Your at-rest heart rate is influenced by endurance training. The typical adult has an at rest heart rateofapproximately72BPM,whereashighlytra

23OpERATIONSWhat to WearWearrubber-soledathleticshoes.Youwillneedtheappropriateclothesforexercisethatallowyouto move freely.How Often S

24Power-Up / Idle ModeThe Console will enter Powe r-Up Mode if it is plugged into a power source, any button is pushed, or if it receives a signal fro

25IfyouselecttheUserproleoption,youhavetwooptions:VIEWSTATSandWORKOUT.UsetheIncrease/Decrease buttons to look at the menu options, a

263. The Console display shows the “Create Custom” prompt. Use the Increase/Decrease buttons to move to the YES or NO option. To start setup of your

27Delete User1. From the Power-Up Mode screen, push START/ENTER and hold for 3 seconds to go to User Setup Mode. If a User profile is set up, the Co

282. Use the Increase() or Decrease() buttons to select a user (guest or custom) and push START/ENTER. If you select a custom user (not Guest User)

29Over time, you will output more power at a certain Heart Rate. Compare your Fitness Scores to see your improvement.Results / Cool Down ModeAfter a w

3IMpORTANT SAfETY INSTRUCTIONS — ASSEMBLY!This icon means a potentially hazardous situation which, if not avoided, could result in death or serious in

30The Stats option in the User profile menu lets you look at the recorded data or delete it.1. Push START/ENTER at the Power-Up Mode screen. The Cons

31CONSOLE SETUp MOdEThe Console Setup Mode lets you set the units of measure to either English or Metric, change the machine type, or see maintenance

32This page intentionally left blank.

33Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is necessary to do the necessary tasks.!E

34Maintenance PartsA Console I Levelers Q Brake AssemblyB Console Mast J Data Cable R RPM SensorC Pedals K HR Cables S Speed Sensor MagnetD Crank Arms

35TROUBLESHOOTINgCondition/Problem Things to Check SolutionNo display/partial display/unit will not turn onCheck electrical (wall) outletMake sure uni

36Console displays “E2” error codeCheck data cable integrity All wires in cable should be intact. If anyare cut or crimped, replace cable.Check data c

37Fan(ifequipped)willnotturn on or will not turn offCheck data cable integrity All wires in cable should be intact. If anyare cut or crimped, rep

38This page intentionally left blank.

39This page intentionally left blank.

4SAfETY WARNINg LABELS ANd SERIAL NUMBERFCC Compliance!Changesormodicationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompli

Nautilus® Bowflex® Schwinn® fitness Universal®004-4604.080311.C

5SpECIfICATIONS53”(135.0 cm)31.6” (80.3 cm) 20” (51.0 cm)Before Assembly Select the area where you are going to set up and operate your machine. For s

6Item Qty Description Item Qty Description1 1 Main Frame 9 1 AC Adapter2 1 Rear Stabilizer 10 1 Left Pedal3 1 Front Stabilizer 11 1 Right Pedal4 1 Sea

7ToolsIncluded Not Included6 mmItem Qty Description Item Qty DescriptionA 4 FlatHeadHexScrewM8x16 E 1 HexBoltM7x30B 4 ButtonHeadHexSc

81. Attach Stabilizers to Frame Note: Make sure the Schwinn® decal on the Rear Stabilizer faces outward from the machine.2. Attach Pedals to Frame

93. Attach Seat to Seat Post and Frame NOTICE: Slide the Seat (12) onto the Seat Post (4) and install the Seat Post in the Frame. Make sure the adju