Schwinn Fitness A40 Uživatelský manuál

ASSEMBLY MANUAL / OWNER’S MANUAL Manual en Español Latino Americano:http://www.schwinnfitness.com

106. Attach Legs to Frame Assembly5. Install the Static Handlebar to the Console Mast Note: Hardware is pre-installed on Static Handlebar and not o

117. Attach Lower Handlebar Arms to Frame Assembly

128. Attach Pedals to Pedal Arms9. Attach Pedal Arms to Legs and Lower Handlebar Arms NOTICE: To avoid damage to the Arms, attach Pedal Arms to Legs

1310. Attach Upper Handlebar Arms to Frame AssemblyL4mm14H154#2X44a11. Attach Media Tray to Console and Install the Console to the Console Mast Note:

1413. Tighten all Hardware Note: Fully tighten all Hardware from the previous steps. Make sure that the machine is level. If necessary, adjust the

1514. Install Batteries in Console Note: The console uses D size batteries (LR20). Make sure that the batteries point in the direction of the +/– i

16BEFOrE yOu STArTMoving the MachineThe machine may be moved by one or more persons depending on their physical abilities and capacities. Make sure th

17ImpOrTANT SAFETy INSTruCTIONSThis icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.Before

18FEATurESA Console K Water Bottle HolderB Swing Handlebar Arm L Contact Heart Rate (CHR) sensorsC Static Handlebar M Power ConnectorD Main Frame Asse

19Console FeaturesThe Console provides important information about your workout and lets you control the resistance levels while you exercise.TheCon

2TABLE OF CONTENTSNautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Customer Service: North America (800) 605-3369, csnls@nautilu

20Speed / DistanceThe SPEED/DISTANCE display field shows the machine speed in kilometers per hour (km/h) or miles per hour (mph) for 6 seconds, then th

21Themostefcientproceduretoburnfatduringexerciseistostartataslowpaceandgraduallyincreaseyourintensityuntilyourheartratereach

22OpErATIONSWhat to WearWearrubber-soledathleticshoes.Youwillneedtheappropriateclothesforexercisethatallowyoutomovefreely.How Often S

23Changing Resistance LevelsPush the Increase() or Decrease() buttons to change the resistance level at any time in a workout program.Profile Progra

24mAINTENANCERead all maintenance instructions fully before you start any repair work. In some conditions, an assistant is required to do the necessar

25Maintenance PartsA Console M Shroud, Right Y HR CableB Static Handlebar N Rails Z Data CableC Console Mast O Leveler AA Battery BayD Water Bottle Ho

26Replacing the Console BatteriesIf the Battery Indicator comes on, replace the batteries in the back of the console with fresh batteries. Make sure t

27TrOuBLESHOOTINGCondition/Problem Things to Check SolutionNo display/partial display/unit will not turn onCheck electrical (wall) outletMake sure uni

28Console shuts off (enters sleep mode) while in useCheck data cable integrity All wires in the cable should be intact. If any are cut or crimped, rep

29Who Is CoveredThis warranty is valid only to the original purchaser and is not transferable or applicable to any other person(s).What Is CoveredNaut

3ImpOrTANT SAFETy INSTruCTIONS — ASSEmBLyThis icon means a potentially hazardous situation which, if not avoided, could result in death or serious inj

Nautilus® Bowflex® Schwinn® Fitness Universal®8002251.081513.CEN

4SAFETy WArNING LABELS AND SErIAL NumBErFCC ComplianceChangesormodicationstothisunitnotexpresslyapprovedbythepartyresponsibleforcomplia

5Before Assembly Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a hard,levelsur

6pArTS17A decal has been applied to all right (“ R ”) and left (“ L ”) parts to assist with assembly.Item Qty Description Item Qty Description1 1 Fram

7HArDWArE / TOOLSToolsIncluded Not Included4 mm5 mm(recommended)Item Qty Description Item Qty DescriptionA 6FlatHeadHexScrew,M8x20J 2ShaftB

8Note: Do not fully tighten the Hardware until the machine is completely assembled.1. Attach Front Stabilizer to Frame2. Attach Rail Assembly to Fra

93. Connect the Console Cable NOTICE: Align the clips on the cable connectors and make sure the connectors lock. Do not crimp the Console Cable.55